Trendnet Cable Modem/xDSL TW100-W1CA Manuale Utente

M73-APO07-080 TW100-W1CA IP Sharing for Cable Modem/xDSL User Manual

- 6 - CONFIGURATION The product can be configured through the setup program (included in the package), through a terminal emulation program, such as

- 7 - Figure 5 Select the device that you would like to setup and then click Configure. Figure 6 The configure dialog box is categorized into sever

- 8 - Firmware Version: Read-only. Device/Computer Name: For you to enter a descriptive name for identification purpose. Some Internet Service Provi

- 9 - TELNET management…: Checking this item lets you manage this device remotely from outside of the network through Telnet. ?? Default: disabled.

- 10 - Continuous IP address pool starts at The starting address of this local IP network address pool. The pool is a piece of continous IP address s

- 11 - SubNetmask4: Provided by our ISP. Gateway/DNS server #1/DNS server #2: These values will be automatically provided once you click “Obtain glo

- 12 - Figure 11 Port Type: please select the port type (TCP or UDP) for the port number that was entered earlier. Note: Maximum 12 Server Entries i

- 13 - Figure 12 Network Adapter Address Filter: Filter according to local computer’s network adapter MAC address. Figure 13 Network Adapter’s MAC

- 14 - Remote IP: Filter using the IP address of a remote server (i.e. Web Server). Figure 14 TCP/UDP Port Filter TCP port: filter according to the

- 15 - Configuration in Terminal Program Mode You can use terminal emulation on your PC/workstation for the initial and future configuration of your

FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC R

- 16 - Figure 18: COM 1 Properties 8. Power up the product. How to start Telnet 1. The instructions below are for using this unit at its default s

- 17 - 333 Figure 20 Starting the Configuration 1. Once the connection is made successfully either via HyperTerminal or Telnet, the following i

- 18 - TERMINAL COMMAND Type ? or help to list the main menu commands as below. command>help Dual Ethernet IP Share for Cable/xDSL Modem, versio

- 19 - ?? At command>, type in passwd and hit “Enter” to enter the password setup screen. ?? Password can be up to six characters long. ?? Passw

- 20 - Obtain global port configuration from ISP : [Yes] .. under claiming IP address of global port : [0.0.0.0] SubNetmask of global port : [0.

- 21 - SubNetmask of global port [0.0.0.0] : Device name (0 to 20 characters) [Untitled] : Domain name (0 to 36 characters) [Domain] : Gateway [0.0

- 22 - Internet to the local network are blocked. Computers outside the Intranet are allowed to access specific ports by using the vserv command. The

- 23 - command>release Give up the obtained global port configuration Note: if you choose NOT to obtain the global port configuration from your IS

- 24 - 192.168.10.4 0080-C8F8-8A64 2:55:48 Victoria 192.168.10.5 0080-C8F8-8A64 expired SNL Total 5 user, 3 active lease. E

- 25 - tcp 7 192.168.10.31 1033 4138 211.75.84.154 80 0 GERNERAL tcp 7 192.168.10.32 1729 4139 140.113.39.195 110 0

TABLE OF CONTENT INTROUCTION...

- 26 - Item Type Action From To ==== ====== ======= ================ ================ 1. MAC Filter 0080C8123456 IP a

- 27 - With the combination of the above two filter examples, the workstations with IP address 192.168.0.25, 192.168.0.26, 192.168.0.27, … and 192.16

- 28 - FIRMWARE UPGRADE System Requirements ?? One free COM port on PC. ?? A pin-to-pin RS-232 cable. One end is 9 pin male connector, the other end

- 29 - Figure 22 5. When the following screen appears, power on the device. Figure 23 6. Expect to wait for a few seconds before the upload progr

- 30 -

- 31 - CHANGING PASSWORD The device has no password at default. It is recommended that you change the default passwords to ensure that someone canno

- 32 - Note: In default, there is no password, so just leave this entry blank and hit “Enter” to continue. type new password (0 to 6 characters) : **

- 33 - PPP OVER ETHERNET (PPPOE) What is PPPoE? PPPoE is known as a dial-up DSL service. It is designed to integrate the broadband services into the

- 34 - FAQ Factory Reset If for any reason, e.g. password being forgotten, you have to reset this device to factory default settings. By performing

- 35 - addresses on a LAN with an existing DHCP server may cause problems throughout a network. It is recommended you disable other DHCP serves on th

PERFORMING FIRMWARE UPGRADE... 28 CHANGING PASSWORD...

- 36 - Figure 27 B. Choose the "Virtual Server" tab: C. Enter one of the port numbers that your application requires and press "Brow

- 37 - Figure 29 E. Press Add. Repeat this process for each individual port you need to open. Figure 30

- 38 - F. Press Save. Wait 30 seconds for the device to reboot and then try the application again. It may be necessary to restart your application o

- 39 - Figure 32 Check the physical connectivity of local network. Check if both the LEDs of Local and Global on the product’s front panel are green

- 40 - Diagnosis TCP/IP Network Diagnosis Execute WINIPCFG.EXE or PING.EXE for TCP/IP network diagnosis. WINIPCFG The WINIPCFG program (for Win95, 9

- 41 - Figure 35: IP Configuration On the top, the “Host Name” and “DNS server” of the computer are configured to call when it is looking for a name

- 42 - For example, to find the server 168.95.192.1, type the following command at the MS-DOS prompt: C:\>ping 168.95.192.1. PING can be executed

- 43 - Getting Technical Support You can also contact us for technical support. TRENDware www.trendware.com E-mail: [email protected] Phone:

- 44 - APPENDIX A SPECIFICATIONS Protocols IP, NAT, ARP, ICMP, DHCP Management/Setup Locally, via direct serial cable connection through Console

- 45 - APPENDIX B SUPPORTED INTERNET APPLICATIONS Application Settings for Outgoing Connection Setting for Incoming connection ICQ98a,99b None N

- 1 - INTROUCTION IP Share device is designed for IP address simplification and conservation, as it enables private IP Internet works that use non-re

- 2 - Features ?? Supports PPPoE. ?? Supports VPN.(PPTP pass through). ?? Explicit LED indication for Internet connection. ?? Supports Internet appl

- 3 - LED Color Status Indicator Glowing Dim Flashing ? Power Green Power On Power Off N/A. ? Local Link Green Connected to a LAN

- 4 - System Requirements Your system must meet the following requirements to use the product’s Setup program. If you are using a Unix or apple based

- 5 - FACTORY DEFAULT SETTINGS Password The default setting for password has been left blank in the factory. Press Enter then you are logged in for